Search results

  1. euromut

    Thorens Td160 build

    Thank You all. Unfortunately, I cannot find the source for the Thorens Logo. I am pretty sure I found it on eBay from Switzerland. I see some, but not made like mine. Mine is Chrome Plated Brass.
  2. euromut

    Thorens Td160 build

    So this project went dormant for quite a while. Access to friends shops due to Covid, slowed my down a bit. I had to buy some tools to get it done. Decided I could do better. So I tore the whole thing down again. I swapped out the top plate with one from an earlier, near perfect TD160...
  3. euromut

    Rega Owner's Thread

    Let me see if I can verify that motors dimensions. I am not sure if its the same size/shape as the 24v. The 24v has a 2 inch diameter.
  4. euromut

    Rega Owner's Thread

    I just want to make sure your using a 24V motor. Also, can you measure the height between the bottom of your plinth, and the cutting board its sitting on. My mount is based on 1 inch high feet.
  5. euromut

    Rega Owner's Thread

    I was working on this a year or so ago, but a divorce got me pretty distracted. I have a prototype I am willing to let someone try. I am still using the original Delrin prototype on mine. From that, I designed and build a 3D printed model. It will sit on the surface under the turntable. and...
  6. euromut

    Pics of your listening space

    Its been a while, Still enjoying my 60s cave.. Going to rock wool and drywall the ceiling eventually.
  7. euromut

    Pics of your listening space

    I think your daydreaming happy thoughts. They look like wooden crates.
  8. euromut

    Using ADS L400s and a line level Sub

    Actually, upon further inspection. The sub-woofer I will be using only has speaker level in, not in/out. So I guess that answers my questions. It seems I always have to do something weird to setup my sub. My main system uses a derived center channel output (an HH Scott thing) which is a pre amp...
  9. euromut

    Using ADS L400s and a line level Sub

    I am setting up a 2nd system with some A/D/S L400s and a Luxman L210. I would like to add a subwooder, but the Luxman has no output. I have a couple of subs with speaker level in/outputs (Pass through). I was thinking of wiring them in parallel so as not to pass the L400s through the subs...
  10. euromut

    Pics of your listening space

    Last night I was working on cleaning up my newly acquired A/D/S L400s. They will be part of my Bedroom setup, So I decided to do a little tinker and tune until that space is ready. Temporarily on the bar in my main listening room. I may decide to add a pass through subwoofer to fill out the...
  11. euromut

    Pics of your listening space

    Making a little more progress. I have some of the new circuits in place for power. The Thorens, Rega, and Revox are all hooked up through the HH Scott. Teac is through the Onkyo for now. First time I've had the Rega lit up in a couple years.
  12. euromut

    Pics of your listening space

    Yes, It is a wood burning fireplace. I will be converting it to vent-less open gas logs eventually. Our upstairs fireplace already has a glass and log insert.
  13. euromut

    Pics of your listening space

    Thank you. They are the previous generation, Monotor Audio, Silver 8. They are fantastic. The Audiomods arm was prewired. I think the problem may be with the ground. Or some of the varnish rubbed off the wires. In any even the right Chanel is very quiet. I’m hoping to just repair the...
  14. euromut

    Pics of your listening space

    a Little bit of progress. I positioned and wired 6 of the recessed LED lights. My Thorens is down for the moment for a tonearm rewire, so for now I am "suffering" with my RP6. They will both be part of the permanent setup. The Rega will be going on a wall mount, which I think will go to the...
  15. euromut

    Pics of your listening space

    I had a local metal plating company do it. I did end up with some slight bubbles under the copper. This appears to be an issue with the zinc aluminum out gassing. I guess if you have it brass or rhodium plated, then copper it will help eliminate this. I will see how bad the bubbles get. It...
  16. euromut

    Pics of your listening space

    Thank you, Its an Audiomods Series 5 Micrometer arm.
  17. euromut

    Pics of your listening space

    The lighting in my new listening room is horrible. So this is the best I have for now. The finish is not perfect, but I like the contrast.
  18. euromut

    Thorens Td160 build

    After moving to a new house, I am getting some hum. I am going to be adding a separate ground lug (as some of you already suggested). I modified the housing for a Neutrik RCA, 3D printed an insert to adapt it for a 4mm Banana Jack. I'll be mounting it inline, to the right of the existing RCAs.
  19. euromut

    Pics of your listening space

    Thank you so much. It is definatly my baby. I need a better picture of it now with the Copper plated platter.
  20. euromut

    Pics of your listening space

    Thank you. The center is not set up yet, just set in place. For 5.1 I use an Onkyo TX-NR747(Its actually very musical for a HT receiver). Which also brings a pair of Monitor Audio, Radius 90s (For rears), and a SVS SB-2000 sub into play. I have a custom made switch that allows me to select...
  21. euromut

    Pics of your listening space

    Thanks everyone. The drywall ceiling will be a ways away. After I do much better lighting, and new dedicated electrical for the gear. So I took the time to start setting up my 2 Channel system. Untitled by swedg1, on Flickr
  22. euromut

    Pics of your listening space

    The beginning of my new listening space. I've already dropped the old acoustic ceiling. I'll be running new power for my gear, and putting in LED can lighting before putting up drywall. I can't wait to get things set up.
  23. euromut

    Converting Revox B77 MkII to HS IEC

    Finished up the first board. Plenty more to go.
  24. euromut

    Converting Revox B77 MkII to HS IEC

    Well, I'm getting closer. I went through the machine last night. Verified the board versions, and confirmed my parts stock. Also double checked the pin spacing for some of the WIMA film cap replacements I have. Everything looks to be in order. I also had a very plesant stop at a local...
  25. euromut

    Pics of your listening space

    I cant wait to get this moved into its new location. Sorry, I was just admiring myself again.
Back
Top Bottom